The Correct Use Of The Spring

For Spring Use, Please Avoid The Following Improper Use:

(1) Use Exceeding The Maximum Amount Of Compression (300,000 Return Conditions, And The Use Of The Connector For Long-Term Use) The Pressure Will Cause Breakage, And The Use Of Close To Long Use Will Make The Compression Spring Wire Gradually As A Result Of This, The Higher The Number Of Springs Is, The Higher The Load Curve Is, And The Higher The Stress Is, The More The Spring Breaks. Do Not Use More Than 300,000 Cycles.

(2) The Use Of Non-Preloading Springs Are Distorted Due To Gaps Causing Springs To Vibrate Up And Down. If There Is Preloading, Springs Are Relatively Stable.

(3) Horizontal Use Of The Spring When The Spring Is Used Horizontally, The Guide Pin And The Spring Are Worn And Broken.

(4) Use Without Spring Guide When Using In The Case Of Dancing Spring Guide, It Is Easy To Cause Distortion Of The Spring Bottom And The Body. The Local High Pressure Of The Twisted Part Is The Cause Of The Spring Break, Please Use The Inner Diameter Guide Pin Or Outer Diameter Guide And Other Devices.

(5) When The Flatness Of The Mounting Surface Is Poor When The Parallelism Of The Mounting Surface Is Poor, The Spring Will Be Distorted, And High Pressure Fracture Will Occur Locally, And When The Parallelism Is Poor, The Spring Will Be Distorted And Over 300,000 Cycles Will Cause The Spring To Break. Please Improve The Parallelism Of The Mounting Surface Under A Condition Of No More Than 300,000 Uses.

(6) When The Internal Diameter Of The Spring And The Gap Between The Guide Pin And The Guide Pin Are Too Small, It Will Cause The Impact Wear Of The Internal Diameter. The Wear Part Is The Cause Of The Spring Break. Conversely, If The Gap Is Too Large, The Spring Will Be Distorted And Broken. The Best Is The Internal Diameter Of The Spring. -1.0mm Or So. For Springs With Long Free Length (Free Length/Outer Diameter Greater Than 4), Please Use Segment Steps Or Guide Pins To Avoid Collision With Guide Pins When The Spring Body Is Twisted.

(7) Outer Diameter Of Spring And Countersunk Hole If The Countersunk Hole And The Spring Clearance Head Are Too Small, The Force Of Concentrated Fracture Will Be Caused By The Expansion Of The Outer Side And The Friction Of The Countersink Hole Due To The Compression Of The Spring. The Preferred Countersink Diameter Is The Outer Diameter Of The Spring +1.5mm. Use A Countersunk Hole For Longer Springs.

8 must-know techniques for keeping your kitchen cabinets sparkling cleaning

Different cabinet surfaces require different cleaning techniques. Whether your cabinets are stained, painted or laminate, they all need special attention. Here are a few easy tips and cleaning recipes for keeping them looking their best.

Solid wood cabinets. You will want to thoroughly clean and oil your stained wood cabinets once or twice a year. Clean them with a mixture of seven-eighths distilled white vinegar and one-eighth rubbing alcohol, with a few drops of dish soap added. Wipe the cabinets down with this cleaning mixture using a microfiber cloth. Next, rinse the cabinets completely with warm water then use a furniture oil that contains beeswax to seal the finish. This process will keep your cabinets looking new for a long time.

Painted cabinets. Painted cabinets need to be cleaned with a gentle cleaner, rinsed and dried. If you use a harsh cleaner on the painted surface, the cleaner can actually remove the paint.

Instead, mix up a DIY cleaner of distilled white vinegar and a few drops of dish soap, but this time leave out the rubbing alcohol. Try putting this mixture into a spray bottle to better control the amount. After spraying, wipe the cabinets down with a damp microfiber cloth. Finally, use another clean microfiber cloth to dry.

RELATED: The Top 8 Trending Styles for Kitchen Cabinets

Black kitchen cabinets. Whether painted black or stained ebony, black cabinets create a chic look in a kitchen, but they do take some extra care. Every water and grease spot will show up on these cabinets as will an accumulation of dust. You should get into a routine of wiping them down at least once a week with a damp microfiber cloth. It will only take a few minutes but doing this will prevent nasty buildup.

White cabinets. White cabinets provide a fresh, clean look to many a kitchen, but they also show every fingerprint and scrape. Just like black cabinets, white ones should be wiped at least once a week with a damp microfiber cloth. You should also have a small bottle of matching white paint on hand to fix chips and scrapes that are bound to show up with white cabinets.

Laminate cabinets. Laminate cabinets are the easiest to keep clean because their surface doesn’t have porous wood grains that absorb dirt and grease. A damp microfiber cloth and minimal elbow grease once a week usually does the trick.

For deeper cleaning, the same DIY cleaner for stained wood cabinets will do the trick. Vinegar is a natural acid and will work to lift off stuck-on food. The alcohol cuts through grease and oil. And the few drops of dish soap help to create a mild lather for easier cleaning.

RELATED: Replace Grimy Cabinet Pulls With Shiny New Ones Today

Get a handle on it. Areas around handles can get very sticky. The oils from your hands can mix with the finish on your wood and break down the finish. You can prevent this from happening by wiping the areas around the handles with a damp microfiber cloth. If you get that sticky buildup, you can wash it off with a gentle hand soap mixed with some rubbing alcohol.

To really get at hidden grime, it is recommended that you remove your pulls and knobs at least once a year and clean the fronts of your cabinets before putting handles back on.

RELATED: Don’t Forget to Wipe Down and Clean Your Kitchen Gadgets Too

Nooks and crannies. Cabinets with nooks and crannies need extra care to remove dirt, dust and buildup in those tight places. You can use a microfiber cloth wrapped around a table knife to get into flat areas that need to be cleaned. While a pointed knife will also work, just be careful it doesn’t penetrate the cloth and scratch or nick the wood. A toothpick will also work for tight corners and small crevices.

Around the stove. Cabinets around your stove can get spattered with grease and oil. You can clean them quickly with a spray bottle of vodka and a few drops of Castile soap. The vodka will work to cut through the grease and oil, while the soap will lift it away. Make sure to rinse the cabinets after with a damp microfiber cloth.