How to Solve MB SD C4 Plus DOIP WiFi Connection Error

MB SD C4 Plus DOIP WiFi connection problem: An error message prompts as shown in the following picture. And there is something wrong with the WIFI. Is possible to use LAN cable to connect?

Solution Advice:

There are two connection methods for MB SD C4 PLUS: by Wifi or network cable.

If it failed to connect by WIFI, please use network cable instead of it.

If the WLAN is ok, don’t modify the IP setting.

For the connection problem, please watch the MB SD C4 plus DOIP WiFi Setting video to understand clearly:

How to Configure VCDS & Diagnostic Cable for Your Laptop

           

This article show a guide on how to configure VCDS diagnostic cable for you laptop

Procedures:

Connect the USB end of your USB Interface or the Serial end of your Serial Interface to the correct port on your PC. If your PC is further from the vehicle’s diagnostic port than 6 feet,
connect an approved Extension Cable between the PC and the Interface.

If you are using a Serial Interface then you can proceed to step #4. If you are using a USB
Interface, a message like this should pop up:

The drivers many install automatically in Windows 7 or Vista. If you are using XP or W2000, click on the Found New Hardware message and the Found New Hardware Wizard should start up. If you are prompted with the choice, pick “No, Not This Time” when asked if you want to connect to the Internet to search for drivers. Select “Install the software automatically (Recommended)” then click [Next >]
The process should be automated but you may need to click “Continue Anyway” part way through the process.

If, for some reason, you installed the USB Interface without following the above instructions, and VCDS does not work correctly, go into your PC’s Device Manager while the USB Interface is connected.

You can find the Device Manager by right-clicking on My Computer in XP or on Computer in Vista or 7. Select Manage to bring up Computer Management. On the left side of the screen under System Tools, select Device Manager.

Find the “VCDS Compatible USB Interface” or similar and delete it. It may be under “Other Devices” or under “Universal Serial Bus Controllers”. Next, unplug the USB Interface from your PC, wait 5 seconds and plug it back in.

Connect the car end of your Interface to your vehicle’s Diagnostic Port.

If your vehicle has a 2×2 port (some pre-1996 vehicles), then use the optional 2×2 Adapter between the Interface and the ports in the car. This is included in the Pro-Kit.

Turn the vehicle’s ignition switch to the ON position. Make sure the key is turned far enough that the dash lights are fully illuminated. The engine may either be running or stopped.

Start the VCDS program on your PC through either the Start Menu or the VCDS icon on your Desktop.

From the Main Screen in VCDS click the [Options] button to go into the Options screen.

Once you are in the Options Screen,Select the correct port for your PC’s USB Port (USB) or Serial Port (typically COM1 or COM2) and click the [Test] button. Ensure that VCDS finds your interface.

You should see a message like this:
If the Interface Status is “Not Found!”,check the connections at the car and PC.Make sure both are plugged in securely.Serial Interfaces get their power from the vehicle so they will not be recognized at all if not plugged into a car.
Adapter Type should always be “RossTech” followed by the name of the Interface such as “HEX-USB+CAN”.
Version indicates the firmware version of your Interface. It may be updated by new versions of VCDS, if so follow the prompts on the screen.

Once you have tested successfully, click [OK] then click [Save] to apply this configuration,you will be returned to the Main Screen. Click on [Select] to view the Select Control Module Screen. Select one of your car’s Control Modules such as Engine.
Note: Your car will not have all the Control Modules listed in VCDS, only the functional ones that were installed in your vehicle.

After VCDS has connected, click on [Fault Codes] to check for Fault Codes (DTCs).Repeat the process for each of your car’s Control Modules.

Digimaster 3 Adjust mileage on Toyota Prius 2014& 2015

Can Toyota Prius 2014& 2015 correct odometer by Yanhua Digimaster 3 and yanhua ICP tester?

The answer is only need digimaster 3 is ok.

How to do?

It is easy to adjust mileage by digimaster 3. It needs to dismantle the dashboard and read the data.

Please follow the steps to operate as below.

1.Open Digimaster 3 home page

2.Select Meter System-> Japan& Korea-> Toyota-> Pirus

3.The system will prompt what chip is.

Chip 93C46, 93C66 and 93C86 can be supported

4.Find the car chip and check whether it is consistent with the prompt or not

If it is, disassemble it and weld to OBP adapter

5.Connect with Odometer Correction Tool digimaster 3 to read data

6.And follow the prompt to change mileage

How to Solve SVCI 2020 2019 BMW DTC Database Missing Error

           

When you open the ABRITES Commander BMW v10.4/v10.5 software with SVCI2020/SVCI2019 device, the following error will be reported when reading the DTC functions.

when you want to program the radio eg function with BMW software, it will appear the error information like below figures.

So in this instruction, Obdii.shop will give you solution to solve this error.

Solution:

Step 1: Open the SVCI2020 software installation directory

Step 2: Enter “C: Program Files (x86)\Abrites Commander Software List\Common2\ ” directory and copy BMW folder to “C: Program Files (x86)\Abrites Commander Software List\Common\” directory.

Frequently Asked Questions About DS708

           

Does the DS708 work on OBD-I (pre-1996) vehicles?
The DS708 currently only supports OBD-II (1996 and newer) vehicles.

Where do I find my register password?
The register password can be found by going to “Setup” then “About”.

How much are updates for the DS708?
The MaxiDAS DS708 comes with one year of FREE updates and technical support. After the first year, it will cost $799 for another year subscription for updates and technical support.

Will I be charged for the years I choose to skip and not update ?
No, you will not be charged for any year that you choose not to update. Once you pay your re-subscription fee of $799, you will be granted full access to all the most current updates, including those you may have missed.

I can get my sensor ID’s and wake up my TPMS sensor, but the TS401 will not program the sensor to the vehicle?
The vehicle will first need to be placed into registration mode to learn the new TPMS sensor ID or positions. To view how to place the vehicle into registration mode, first select the correct Make, Model, and Year, then once at the vehicle screen press the “?” button on the tool. This will show you the OEM part number and relearn information. Please note that some vehicles will need a scan tool, such as our MaxiCheck Pro or DS708, to place the vehicle into registration mode.

When using the TS401 with the DS708, will I ever connect my TS401 directly with my DS708?
While the DS708 and TS401 work in conjunction with each other they do not communicate directly with each other. You will either place the vehicle into registration mode with the DS708 and then activate each TPMS sensor or retrieve the Sensor IDs using the TS401 and enter them manually into the DS708.

My Autel Scanner MaxiCheck Pro does not include the TPMS or SRS functions, why is this?
The TPMS and SRS functions were added to the tool as software updates and are now available using the Autel PC Suite. For assistance on updating please view our Updating FAQ section, Updating FAQs.