avr で CP/M を動かす記事（https://spritesmods.com/?art=avrcpm）を参考に作成した。
注意点
インターネット上で複数の記事があるが、途中でpin接続が変更になっている
初期にはポートCの接続が以下のようになっていたが、
=== avrcpm-0.1.tgz ===
;Port C
.equ ram_d1 = 0
.equ ram_w = 1
.equ ram_d2 = 2
.equ ram_d4 = 3
.equ ram_d3 = 4
.equ ram_cas= 5
dram_getnibble:
andi temp,0xf0
sbic pinc,ram_d1
ori temp,0x1
sbic pinc,ram_d2
ori temp,0x2
sbic pinc,ram_d3
ori temp,0x4
sbic pinc,ram_d4
ori temp,0x8
ret
ある時期を境に以下のように変更されている。
avrcpm_upd2
===config.inc===
;Port C
.equ RAM_D0 = 0
.equ RAM_D1 = 1
.equ RAM_D2 = 2
.equ RAM_D3 = 3
.equ RAM_W = 4
.equ RAM_CAS = 5
=== z80.asm ===
dram_read:
cli
DRAM_SETADDR xh, ~0,(1<<ram_ras), ~(1<<ram_a8), (1<<ram_oe)
cbi P_RAS,ram_ras
DRAM_SETADDR xl, ~(1<<ram_ras),0, ~((1<<ram_oe)), (1<<ram_a8)
cbi P_CAS,ram_cas
cbi P_A8,ram_a8
dram_wait DRAM_WAITSTATES ;
in temp,P_DQ-2 ; PIN
sbi P_CAS,ram_cas
cbi P_CAS,ram_cas
andi temp,0x0f
swap temp
dram_wait DRAM_WAITSTATES ;
in temp2,P_DQ-2 ; PIN
andi temp2,0x0f
or temp,temp2
sbi P_OE,ram_oe
sbi P_CAS,ram_cas
sbi P_RAS,ram_ras
sei
ret
micro SDは以下の手順でパーティションを切り、fat16とし、https://www.mikrocontroller.net/articles/AVR_CP/M より
CPMDSK_A.IMG〜CPMDSK_C.IMGをダウンロードし書き込みを行った。
# /sbin/fdisk /dev/sdb
Welcome to fdisk (util-linux 2.33.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Device does not contain a recognized partition table.
Created a new DOS disklabel with disk identifier 0xd9d7c804.
Command (m for help): p
Disk /dev/sdb: 28.9 GiB, 30979129344 bytes, 60506112 sectors
Disk model: Flash Reader
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xd9d7c804
Command (m for help): p
Disk /dev/sdb: 28.9 GiB, 30979129344 bytes, 60506112 sectors
Disk model: Flash Reader
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xd9d7c804
Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)
e extended (container for logical partitions)
Select (default p): p
Partition number (1-4, default 1): 1
First sector (2048-60506111, default 2048):
Last sector, +/-sectors or +/-size{K,M,G,T,P} (2048-60506111, default 60506111): +100M
Created a new partition 1 of type 'Linux' and of size 100 MiB.
Command (m for help): p
Disk /dev/sdb: 28.9 GiB, 30979129344 bytes, 60506112 sectors
Disk model: Flash Reader
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xd9d7c804
Device Boot Start End Sectors Size Id Type
/dev/sdb1 2048 206847 204800 100M 83 Linux
Command (m for help): t
Selected partition 1
Hex code (type L to list all codes): 6
Changed type of partition 'Linux' to 'FAT16'.
Command (m for help): p
Disk /dev/sdb: 28.9 GiB, 30979129344 bytes, 60506112 sectors
Disk model: Flash Reader
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xd9d7c804
Device Boot Start End Sectors Size Id Type
/dev/sdb1 2048 206847 204800 100M 6 FAT16
Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table.
Syncing disks.
# /sbin/mkfs.vfat /dev/sdb1
mkfs.fat 4.1 (2017-01-24)
