Attention on SuperOBD SKp-900 Advantages

OBD2 key Programmer SKP-900 key programmer is a hand-held device for reading and programming auto transponder keys, auto remote keys and auto smart keys. It is strong in functions, easy to use, and also cost-effective in price, which is the best choice for locksmith shop and even for DIY users.

Only a few weeks ago, I bought a SKP-900 key programmer on Autonumen.com, Although I did not use it for many time, but its strong function cannot describe beyond words. And I tried to conclude several reasons why it is worth buying as follows:

1. Wide car coverage

Europe: Alfa, Audi, Citroen, Fiat, Jaguar, Opel, Peugeot, Renault, Rover, Smart, Skoda and VW.

America: Buick, Cadillac, Chevrolet, Chrysler, Dodge, Ford, GM, Jeep, Land Rover, Lincoln

Asia: Acura, Honda, Hyundai, Infiniti, Kia, Lexus, Mazda, Mitsubishi, Nissan, Proton, Ssangyong, Subaru, Suzuki, Toyota

China: Brilliance, BYD, Chang’an, Chang Feng, Chery, Dong Feng, Dong Feng Nissan, FAW, Geely, Great wall, Ha Fei, Hainan Mazda, JAC, Jin Bei, Li Fan, Lu Feng, Luxgen, Maple, MG, Roewe, Zotye 5008

2. Easy to update

1) Register online with the Dealer code 1001

2) After registration, update file will be uploaded. Then you will find it in “My Update” when you log in the Official Western again. (This period will approximately take 2 days)

3. For many vehicles, Pincode is not needed when programming key

4. It is able to read pincode for many vehicles

5. Update

SKP-900 provides frequent free update, usually monthly update.

6. Cost-effective

Really helpful guide to buy a MB Star diagnostic system

I can help you out with getting a MB Star Diagnostic system.

I have a lot of experience with setting up these systems.
The C4 (MB SD Connect C4) units are nice because of the LAN cable connecting the unit to the laptop, as with high quality electronics there seem to be no problems with these units.

I do prefer the MB Star C3 units just because they seem to hold up much better than the MB SD C4’s. The only downside to the C3 multiplexer is the requirement of a serial port on the laptop and the big bulky cable that goes from the head to the laptop.

Software:
Many of the chinese setups you see that sell you a hard drive and “will work with any laptop” are just VM ware installations. Basically a virtual windows setup.. There is no reason to go this route, they are prone to crashing and much slower than native (software installed strait into windows) setups.

There are many different versions of the MB Star diagnostic software and each have their up’s and downs. You can get the 2014 software that will work with cars just being pulled off the ships. But most people wont be working on the latest cars so I always suggest older versions from 2010 to 2012. As the software keeps being updated by Mercedes they remove more and more features limiting what you can do as far as basic programming goes as well as other small things here and there..

You can be able to SCN code control units with one of these setups. Mercedes has everything setup to connect to their internet databases for verification to do SCN coding and requires a license you need to purchase.. It is technically possible to do, but for most independent shops its not worth the cost. Basic coding/programming of control units can be done with these systems, but like I said you cant do everything..

Of course these systems do all your basic reading erasing of codes, they have guided troubleshooting in them as well. You can actuate components and read data outputs.

Im sure you get the picture by now.. These can be setup on pretty much any laptop you want with some limitations. SSD drives or just normal hard drives.. makes no difference when you are doing everything from scratch like I do..

If your interested in purchasing a system feel free to contact autonumen.com. They will answer any questions you might have and can figure out exactly what kind of setup you want. They also provide a 1 year warranty on all my systems, which is something you don’t really get when your faced with shipping a package back to china and hoping that all works out.

Autel MaxiSys Elite Diagnostic Tool Common problem solving methods

1. updating MaxiFlash Elite to firmware 3.21? My maxisys communicate with the MaxiFlash J2534 but Maxiflash elite cannot communicate with any cars!
To resolve this problem , go to www.autonumen.com and go support and updates ,and live chat with the representative and they’ll help you to resolve the issue .

2. How to install Google play store in Autel maxisys elite
you can download Google chrome on elite. Just search Google chrome apk file and download and install it. After that you can access pro demand and identifix

3. I’m trying to program BMW car and I cannot. All the hardware are done
You still need to within your free update period , you need a good WIFI connection to your network and internet from your work area , and Autel’s server to access what programming and advanced coding that is available for the year , make, model, and module of the BMW.

4. I may be silly here but my maxisys elite has NO Ethernet port for BMW programming. I have looked all over the tablet. The only ports I have are 2 x usb, hdmi, otg, headphone and power?
1.Yes Autel has a separate adapter for it. You need to purchase it separately.
2. You can buy any Android compatible ethernet-USB adapter from any place. But you have to be sure that works with Android, because if the adapter is just for PC it will not work with the tablet.

5. how to programming the vehicle modules
Autel Scanner Autel MaxiSys Elite / Autel MaxiSys Pro MS908P can only support to program BMW and Benz.

6. My Maxisys Elite Multitask will not turn on.
you need to go to System Setting->App Switcher, please select it.

7. I cannot get my MaxiSys Elite to send reports or anything with the email option. It also do not want to print to my wireless HP Deskjet 4645 altough i pick it up. I have my Maxisys running from my iPad hotspot.
What’s your system version? Please go to Maxisys-Update to download all the latest system version and try again. Our current version can’t support to Wi-Fi printer, so you need to install Maxisys PC link in your PC to print the doc out.

8. I can’t find the vehicles that covereged by maxisys elite in the website
I need to buy this device but first I need to know the vehicles covered,
Plus, how much is for renewal for this device
Function list here: http://pro.auteltech.com/measurecar-1-1.html?m=4 and it’s USD1295 for renewal

9. I have problem with latest Benz update, installation bar goes up to 50% and give message installation error, there is no app Benz in uninstall section.
please check and see is there a benz folder under below path: “ES files EXPLORER—-scan—vehicle–Europe—–Benz”. If there is one, please delete it. Also delete it if you find one under “ES files EXPLORER—scan—download” and “Maxisys—data manager—Apps Uninstall”. Then restart Maxisys elite and re-load and install the Benz software.

10. How to program key for my car ?
Try the following:
IMMO -> 1.Immobilizer Setup -> Add and Delete Keys

11.Which is the activation code because I don’t have it please
Do you mean the register code? You can find it in Maxisys-About page.

12. how I can used e-mail sending by max?
There is an Email app pre-installed in Maxisys , marked in red below. You can set your email account step by step.

13. We just recieved our Maxisys Elite WQ8MAXISYSELITE, but when we try to register it, it says that the product does not exist.
As for your case, please register your device in our website as following steps:
1.Log in our website http://pro.auteltech.com/ with your ID and password.
2.Please click “Product Registration”. Select your product model, fill in the serial No. and register password to finish the registration. As for the serial No. and register password, you can Please touch “About” in the tool, and you will find them.
PS: Please select the right product model and fill in the right register password which can be checked in About page.

14. I am using Autel maxisys Elite, and the internal memory almost full. I bought a SD card (32GB), how can I do that new updates will be written into SD card not internal memory?
Our tool can’t accept external SD card to install vehicle software. It is suggested you format the SD card and download BMW, Benz, VW, which has big size first. Then you can download other vehicles.

GM MDI Tech 3 VS GM tech 2

Many customers ask for this question: what is the difference between GM tech 2 and GM MDI Tech 3 scan tool, if you want buy GM Diagnostics Tools, which one is good? here, we suggest which one is good auto diagnostic tool for GENERAL MOTORS

Autonumen.com GM MDI Tech 3 Diagnostic Scanner:

GM MDI (Multi Diagnostics Interface) is the genuine Vauxhall / Opel dealer diagnostics interface, which when combined with Global TIS, GDS 2, Tech2Win software, and a new laptop, provides full dealer level diagnostics and programming for all Vauxhall /Opel 16 pin vehicles from 1996 to present day. MDI is the quick and easy way to keep customers happy and win new business by offering the exact same functions as the main dealers,.

GM MDI VS GM Tech 2 Scan tool

The GM MDI offers many advantages for workshops looking to upgrade their Tech 2 to the MDI.

– MDI is 20 to 70% faster compared to the Tech 2 for SPS programming, which helps alleviate battery drain on vehicles. This means flashing new ECU software is both quicker and more stable,for example, re-flashing an engine ECU using the Tech 2 could take up to 1 hour, with the MDI it’s just 10 minutes. You can therefore flash 6 cars with the MDI in the same time as it would take 1 with the Tech 2.

– Covers all new Vauxhall models introduced after 2009 with the new Can Bus. These won’t be covered by the Tech 2, they’re exclusive to the MDI.

– The GM MDI has a lower price compared to a brand new & genuine Tech 2.

The Tech 2 will remain an essential tool for years to come, and works well in partnership with the MDI. By investing in the GM MDI, this frees up the GM Tech 2 for quick diagnostic checks. The Global TIS for MDI can be used to update the software on your Tech 2 handset to the latest version. The Tech 2 is also essential if you work on Saab/Isuzu/Suzuki.

Professional Diagnostic Tool GM Tech 2 Diagnostic Scanner

GM Tech 2 is the GM factory scan tool used in all GM dealers since 1996. Model coverage includes all makes and models of GM vehicles including passenger cars, trucks and vans. Model year coverage is from 1992 to 2013. For GM vehicles prior to 1992 you will need a Tech1A or a MasterTech listed below to achieve OEM level functionality.

CAT Caterpillar ET is really a exceptional obd2 solution

As a excellent obd2 solutions,Heavy Duty Diagnostic CAT Caterpillar ET Diagnostic Adapter features a potent function.it not just can Show “Logged Occasion Codes” to show engine more than speeds,Higher temperatures, fuel consumption but also can view ECM’s existing configuration and adjust user settings,perform diagnostic tests and calibrations, and calibrate.Electro-mechanical and electro-hydraulic elements .

Is the Cat Comm III compatable using the computer software CAT Caterpillar ET 2011B Is this an actual caterpillar portion or even a knock off? Thanks.Yes, this is really the genuine CAT adapter, It’s also the ONLY advisable adapter for CAT ET, but obviously other ones will perform. It will function fine for the version you may have, and 2011C is actually the newest version.

What exactly is the distinction between a cat comm II & Cat Comm III. Is one just a usb connection and one serial? Also, will this unit perform with my Cat 3126B marine units? Seriel no. 3GS01797 Thanks. CAT Comm II was a serial port model, but since computers are no longer made with serial ports, they changed the design to a USB and called it a CAT Comm III. So you are correct. This unit works with all CAT engines – Marine, on-highway, and off-highway. On Marine units, I’m not sure where they put the plug, but it should be somewhere near the ECM (Typically). It should be either a 6 pin or 9 pin connector.

Does this operate with CAT 3500 natural gas engines and 3600 natural gas engines? Thanks.If those Professional Diagnostic Tools use CAT Electronic Technician (CAT ET) for the application, it’s going to perform. Can the cat communicate 3 also be used to read detroit and cummins engines if I have the correct software? Yes, it reads both J1708 and J1939 so it can read both of those. Keep in mind that this adapter only comes with the J1939 adapter end, so I would recommend purchasing the J1708 adapter end from me as well if you plan on connecting to some older stuff.

More similar items can be found on www.autonumen.com and any problem please feel free contact us.