How to update Benz MB SD Connect C4 firmware to 2.30

If the Mercedes Benz MB SD Connect C4 diagnostic system reports “DCDI-eErrorCode=204 (204)” error, the possible reason is that the SD Connect Star diagnosis firmware program was deleted so that the Star multiplexer WIFI and configuration are failed. The only solution is to update and flash the firmware. Error screenshots taken below:
25.1
25.2
25.3
Follow the instruction here to updare the MB SD Connect C4 multiplexer firmware:

Update Star diagnosis Connect main unit firmware to 2.30 version:
25.4

1)　Prepare 6 AA5 batteries, follow the pdf document “How to install MB SD C4 rechargeable battery” to installed battery
https://www.autonumen.com/category-163-b0-MB+Star+Compact+C4.html

NOTE: Must use the new battery and make sure battery is fully charged, otherwise may fail to update the firmware. Connect the Star diagnostic Connect multiplexer with computer via LAN cable and connect it with vehicle using OBD main cable. If SD C4 cannot connect to vehicle, feed it with OBD 12V power supply. If SD Connect is not connected with vehicle or fed with OBD 12V power supply, the SD Connect will report 622 firmware update fail error.

2) Open 2012.09 DAS software, browse to C:/program files/SDconnect Toolkit, to check if the three files are included in the folder: Update-automatic, Update-manual, Update-Special, shown as picture below:
25.5

If the file names are incorrect, rename the file.

3) Reboot the computer

4) Start updating firmware. Follow the instruction on “2 Update SDconnect”

https://mega.co.nz/#!PpMnSARa!BCD8S0Dv-9GWYR3OnzQp_TTZZG7zmtE1yBmxmVxsHxI

WIFI CAT ET III Adapter Caterpillar ET3 New Arrival

The old bluetooth cat et adatper iii has stopped production, and you may get the new WIFI CAT Caterpillar ET Diagnostic Interface adapter to replace it, autonumen.com has WIFI CAT ET III Adapter Caterpillar ET3 New Arrival.


WIFI Caterpillar ET3 Adapter III 317-7485 CAT ET III Diagnostic

Car Diagnostic Tools CAT Communications Adapter III 317-7485 is the most current generation on the CAT Communication Adapter group, and replaces the CAT Comm Adapter II.This function is needed for some CAT ET (Electronic Technician) functions.

True 2015A Caterpillar ET3 Adapter III P/N 317-7485 Experienced Diagnostic Adapter for CAT from www.autonumen.com with WIFI

This can be the only encouraged communication device for Auto Repair Software CAT, and the only datalink device which will permit you to properly communicate having a CAT engine on dual datalinks.

Software version: 2015A

2015A Caterpillar ET3 Adapter III Communication:

1. Enables communication in between service tools and engine controls employing numerous data hyperlinks which include J1939/11, DeviceNet (future release), CAT DataLink, and J1708 (ATA) vehicle networks;

2. Flash plan permits adapter firmware upgrades as further features grow to be available;

3. Uses J1939/11, high-speed information link (a part of ADEM III controls), substantially lowering flash times;

4. Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to three minutes).

Should you be trying to find wireless diagnostic interface for cat engines, please you may pick this new WIFI CAT Caterpillar ET Diagnostic Tool III adapter, and you will get 5% off discount should you order it now.

Mercedes BENZ C5 SD Connect Xentry Tab Kit Technical Support

Why MB Star Diagnostic tool is so well-received by thousands of users, its technology and quality is developed after lots of experiments and improvement. Recently, autonumen.com provide a new Star diagnosis bundle, Mercedes BENZ C5 SD Connect Xentry Tab Kit( Newest Mercedes BENZ Diagnostic Tool;Original second hand Mercedes BENZ C5 SD Connect Xentry Tab Kit;With original software and tablet kit;Support BENZ latest protocol)

BENZ C5 SD Connect Diagnostic Tool Description:
Mercedes Benz C5 Xentry Connect diagnostic interface, produced by French ACTIA Company and equipped with Panasonic Xentry-Tab, can test Engine / Transmission / air conditioning /SRS/ABS/ anti-theft system and OBD-II system.
Benz C5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.

BENZ C5 SD Connect Diagnostic Tool Feature:
Efficient diagnostic program and complete vehicle database
Simple and easy-to-use user interface (UI)
High-performance Tab with 4G memory and 13.3 inch LCD touch screen
Advanced upgraded VCI+ communication inter
Support Wired/ wireless connection
Cover all new Mercedes Benz models.
BENZ C5 SD Connect Diagnostic Tool Configuration parameters
A full set of kit configuration
1.Panasonic newest widescreen tab.
2.The original Xentry-Connect by ACTIA
3.Mercedes Benz OBD2 diagnostic cable
Panasonic widescreen Xentry-Tab technical parameters:

OS: windows 7
ultimate CPU:4G
Hard disk memory: 250G
13.3inch touch screen

Xentry-Connect (VCI+) Technical Parameters:

OS: Windows Embedded Standard 7(32bit)
Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
Memory: 4G hard disk with 256GB SSD
Display: 128*64 PX
Battery: 40 minutes (When CPU capacity to 60%)
Weight: 1.9KG
Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ

How to Connect Caterpillar ET Software from your Laptop to ECM

How to Connect Caterpillar ET Software from your Laptop to ECM?

-Open Caterpillar ET Software, it will automatically connect to ECM, Click “Stop Connect”.



-Click on Menu: “Utilities – Preferences”.



-If using Caterpillar Comm Adapter 3, and Mark on “Enable Dual Data Link Service”.



-If using Caterpillar Comm Adapter II, and setting “Ports” (example: COM4) as your COM port at Device Manager.



-If using NEXIQ USB-Link, Choose “RP1210 Compliant Device”, also Click Advanced button to select a specific RP1210.

Solution about MB STAR C4, MB STAR C5 Update and can not test vehicles problems

Solution about MB Star C4, MB Star C5 Update and can not test vehicles problems
1. Make sure your computer hardware version is higher the mb star c4 or mb star c5 version, otherwise, CSD will show update failed . Bootimage can update successfully.
The following picture show how to check the mb star c4 or mb star c5 version

The following picture is show your computer hardware HDD software version

If their software is not same, it no need update ( because factory has upgraded the latest version of the mb star c4 or mb star c5 machine)

2. If customer not use our HDD software, it will appear read vehicle failed problems.
Solution as following
(1) Mb star c4 or mb star c5 supply power to confirm the machine was turn on, like the following picture ( If now show the three icon, it means the mb star c4 or c5 main unit is broken )

(2). connect LAN with computer, confirm computer IP change to172.29.127.118, like the following picture :

(3) change of software using pattern (Because you modify the software for the firmware upgrade mode, the software is not test the vehicles)
The following picture is show the software is upgrade mode.

The following picture is show test read vehicle mode.

Three files name Update_automaticx , Update_manualx ; Update_Specialx
This is read vehicle mode, if can not read vehicle, please change files name, then restart computer