政権交代と二千円札と

本日は衆議院議員総選挙ならびに最高裁判所裁判官国民審査の日であった．ほぼ間違いなく政権交代が実現するだろう．さらに，衆議院における3分の2の議席を民主党が単独で獲得する可能性が大きい．社民党や国民新党を加えた「連立与党」全体では，ほぼ確実に3分の2を超えるだろう．

これだけの議席があるうちに，人権擁護法案や外国人参政権といったものを通すべく，民主党は総力を挙げるであろう．村山談話に続く「鳩山談話」や「福島談話」なるものまで出てくるかもしれない．民主党に投票した人々は，これらの実現を心待ちにしていたのだろうから，まずはお祝い申し上げたい．

ちなみに，以前私は，二千円紙幣の流通促進を求めて民主党に投書をしたことがある．民主党からの返事は「二千円札はおつりとして出すと嫌がる人もいるので慎重に．．．」といったものであった．

夏目漱石との再会

手持ちの小銭や千円札を整理していたところ，千円札のD券(夏目漱石)を見つけた．JRか東急の券売機から釣り銭として出てきたものだろう．珍しくも懐かしい．これも何かのご縁なので，漱石先生には我が家で末永く暮らしてもらうことにした．

二千円札を見て「なつかしい」と言う人が散見されるが，言うまでもなく，これは間違った認識である．

Linmodem on IBM/Lenovo Thinkpad R50

I have installed a Linmodem on an IBM Thinkpad R50 (1829-7PE) with Fedora 11.

The scanModem utility told me that the suitable Linmodem driver is the slmodem (SmartLink modem). Therefore, I have installed the following packages using gpk-application.
- kmod-slmodem-2.6.29-6-217.2.8.fc11.i586-2.9.11-27.fc11.34(i586)
- kmod-slmodem-2.9.11-27.fc11.34(i586)
- slmodem-2.9.11-7.20080817.fc11(i586)
Note that the repositories from RPM Fusion are enabled on the system.

After installing the slmodem, I tried unloading and reloading a kernel module.

# modprobe -r snd_intel8x0m
# modprobe snd_intel8x0m

Then I started slmodemd.

# slmodemd -c JAPAN --alsa modem:1 &

For instance, use "cu" command to comfirm the connection between the PC and the modem.

# cu -l /dev/ttySL0
  Connected.   <== message from the modem
  ATDTxxxxxxxxxx   <== command for the modem
  NO DIALTONE   <== message from the modem

Links below are the texts that generated by scanModem.
  Bootup.txt
  ModemData.txt
  dmesg.txt (1/5)
  dmesg.txt (2/5)
  dmesg.txt (3/5)
  dmesg.txt (4/5)
  dmesg.txt (5/5)
  YourSystem.txt
  scanout.00:1f.6

ダイヤルアップに成功

以前の記事以来，WinmodemというかLinmodemからのダイヤルアップに失敗し続けていたが，ようやく解決を見た．

ダイヤルアップを行うには，minicomやcuを用いてモデムと通信し，そこでダイヤルアップのコマンドATDTxxxxxxxxxxを送信する．すると，今まではそれきりモデムとの通信ができなくなり，slmodemdをいったん殺して改めて起動させるまで通信を再開することは不可能であった．今回は，ATDTxxxxxxxxxxに対して，電話回線がつながっている場合にはかけた先の電話が鳴る，そうでない場合には"NO DIAL TONE"なる返答が返ってくるようになった．

今回は，slmodemdを起動する前に，カーネルモジュールsnd_intel8x0mをアンロード＆リロードすることを試してみた．
---
# modprobe -r snd_intel8x0m
# modprobe snd_intel8x0m
# slmodemd -c JAPAN --alsa modem:1 &
---
これで，たとえばcuでモデムにダイヤルアップコマンドを送ると
---
# cu -l /dev/ttySL0
Connected.
ATDTxxxxxxxxxx
NO DIALTONE
---
のように，きちんと返事が返ってくる．

なお，SmartLink Modem自体は，Fedoraのリポジトリから得られるパッケージをそのままインストールした．今日はそのパッケージにアップデートあったようなので，それもプラスに働いたのかもしれない．

手順をまとめると
(0) SmartLink Modem (slmodemd)をインストールする
(1) モジュールsnd_intel8x0mをアンロード＆リロードする
  # modprobe -r snd_intel8x0m
  # modprobe snd_intel8x0m
(2) slmodemdを起動
  # slmodemd -c JAPAN --alsa modem:1 &
(3) モデムと通信
  # cu -l /dev/ttySL0
のようになる．

なお，マシンはIBM (Lenovo) Thinkpad R50 (1829-7PE)，OSはFedora 11である．モデムはWindows上ではAgereSystems AC'97と表示されていた．モデム周りの詳細な構成については，scanModemによって生成されたテキストを参照されたい．
Bootup.txt
ModemData.txt
dmesg.txt (1/5)
dmesg.txt (2/5)
dmesg.txt (3/5)
dmesg.txt (4/5)
dmesg.txt (5/5)
YourSystem.txt
scanout.00:1f.6

scanout.00:1f.6 from scanModem on IBM Thinkpad R50

CLASS=0703
NAME="Modem: Intel Corporation 82801DB/DBL/DBM "
PCIDEV=8086:24c6
SUBSYS=1014:0524
IRQ=11
SOFT=8086:24c6.MC97
CodecArchived=SIL27
HDA=
CodecDiagnosed=SIL27
slamrTest=
CodecClass=SIL
IDENT=slmodemd
SLMODEMD_DEVICE=modem:1
OPTS=
Driver=snd-intel8x0m

YourSystem.txt from scanModem on IBM Thinkpad R50

This file should NOT be sent to Discuss@Linmodems.org
It has common guidance for modem usage after setup.


Complementation of snd-intel8x0m, slmodemd and a dialer utility
---------------------------------------------------------
THe ALSA (Advanced Linux Sound Architecture) modem driver snd-intel8x0m
provides ONLY a low level access to the hardware. The complementing HIGH
level support for ALSA modem drivers is through a Smartlink utility: slmodemd
An ALSA compatible and compiled slmodemd is in the package SLMODEMD.gcc4.4.tar.gz
with download from http://linmodems.technion.ac.il/packages/smartlink/
Unpack under Linux with:
$ tar zxf SLMODEMD.gcc4.4.tar.gz
and read instructions therein.

Typically the driver snd-intel8x0m will be autoloaded on most Systems.
Then a Root permission command:
slmodemd -c YOUR_COUNTRY --alsa
will announce creation of ports
/dev/ttySL0 --> /dev/pts/N , N some number
The /dev/ttySL0 is a symbolic link to the true modem port /dev/pts/N
USA is the YOUR_COUNTRY default. See other Country alternatives by:
slmodemd --help
slmodemd --countrylist

Should there be a failure report like:
--------
ALSA lib pcm_hw.c:1305:(_snd_pcm_hw_open) Invalid value for card
error: alsa setup: cannot open playback device No such device
error: cannot setup device
--------
First verify that packages providing ALSA audio support are installed.
Names vary with the Linux distribution but they are like "alsa-base"
and "alsa-utilities". In these are installed,
Next try as Root unloading and loading the driver:
modprobe -r snd-intel8x0m
modprobe snd-intel8x0m
Then retest the:
slmodemd -c YOUR_COUNTRY --alsa
slmodemd MUST be kept running throughout a dial out session.

Note that mere loading does NOT establish that snd-intel8x0m is the correct
driver, rather than hsfmodem drivers for Conexant chipset modems. But
snd-intel8x0m may still support readout of Subsystem information.
--------------------------------------------------------------------------
A dialer utility such as wvdial (perferable) is still needed for dialout.
slmodemd MUST be kept running throughout a dialout session.

On some Systems, putting the slmodemd process in the background with an &:
slmodemd -c USA --alsa &
causes subsequent dialout failures.

Read DOCs/Testing.txt for follow through details and DOCs/Smartlink.txt
for additional information.


Interfererce with browser naviagation:
-------------------------------------
Other COMM channels can interfere with browsing under dialout.
Suspect channels set during your scanModem run were shown by: ifconfig
eth0 Link encap:Ethernet HWaddr **:**:**:**:**:**
inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20d:60ff:fe8b:9477/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3119 errors:0 dropped:0 overruns:0 frame:0
TX packets:3420 errors:0 dropped:0 overruns:0 carrier:0
collisions:835 txqueuelen:1000
RX bytes:1190043 (1.1 MiB) TX bytes:934738 (912.8 KiB)

eth1 Link encap:Ethernet HWaddr **:**:**:**:**:**
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xe000 Memory:c0204000-c0204fff

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:22 errors:0 dropped:0 overruns:0 frame:0
TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1868 (1.8 KiB) TX bytes:1868 (1.8 KiB)

A block with "lo" is an internal loopback test and harmless.

However, other COMM channels such as ethernet "eth0" will block browser function
through dialout connections. Domain Name Services (DNS) needed for browsing
will be blocked by an ineffective default usage of the eth0 assigned DNS.

If is wisest to disable bootup establishment of alternate channels in your Control Center.
Depending on your Linux distribution,
one of the following root/admin commands may alternatively be effective:
# ifdown eth0
# ifconfig eth0 down
# /etc/init.d/network stop
# /etc/init.d/networking stop
Be wary that some Systems will periodically try to re-establish internet.
So if browsing should suspiciously fail, recheck with
ifconfig
---------------------------- end COMM Channels --------------------------
fedora is not yet providing pre-compiled drivers for WinModems

The Modem/DOCs/DriverCompiling.txt is a MUST READ,
if you are not experienced in configuring kernel-source/
or get "unresolved symbols" upon driver insertion.

Most recent WinModem fixes are in: http://linmodems.technion.ac.il/FAQ.html

(4) For guidance on automation see http://linmodems.technion.ac.il/archive-fourth/msg03734.html
and the scripts in the slmodem-2.9.n/scripts folder/

dmesg.txt from scanModem on IBM Thinkpad R50 (5)

Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:03/device:04/input/input7
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
intel_rng: FWH not detected
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
input: PC Speaker as /devices/platform/pcspkr/input/input8
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
yenta_cardbus 0000:02:00.0: CardBus bridge found [1014:0552]
yenta_cardbus 0000:02:00.0: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:02:00.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:00.0: TI: mfunc 0x01d21b22, devctl 0x64
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
yenta_cardbus 0000:02:00.0: ISA IRQ mask 0x0430, PCI irq 11
yenta_cardbus 0000:02:00.0: Socket status: 30000086
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x8fff: clean.
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
ipw2100: Copyright(c) 2003-2006 Intel Corporation
thinkpad_acpi: ThinkPad ACPI Extras v0.22
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 1RETDRWW (3.23 ), EC 1RHT71WW-3.04
thinkpad_acpi: IBM ThinkPad R50 , model 0123456
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi:orange:batt
Registered led device: tpacpi:green:batt
Registered led device: tpacpi::dock_active
Registered led device: tpacpi::bay_active
Registered led device: tpacpi::dock_batt
Registered led device: tpacpi::unknown_led
Registered led device: tpacpi::standby
input: ThinkPad Extra Buttons as /devices/virtual/input/input9
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
e100 0000:02:08.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
e100 0000:02:08.0: PME# disabled
e100: eth0: e100_probe: addr 0xc0205000, irq 11, MAC addr 00:0d:60:8b:94:77
ipw2100 0000:02:02.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
eth1 (ipw2100): not using net_device_ops yet
ipw2100 0000:02:02.0: firmware: requesting ipw2100-1.3.fw
Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Intel ICH 0000:00:1f.5: setting latency timer to 64
ALSA sound/pci/ac97/ac97_codec.c:2127: AC'97 0 analog subsections not ready
ppdev: user-space parallel port driver
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
intel8x0_measure_ac97_clock: measured 50928 usecs
intel8x0: measured clock 215 rejected
intel8x0: clocking to 48000
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
Buffer I/O error on device fd0, logical block 0
end_request: I/O error, dev fd0, sector 0
Buffer I/O error on device fd0, logical block 0
end_request: I/O error, dev fd0, sector 0
Buffer I/O error on device fd0, logical block 0
device-mapper: multipath: version 1.0.5 loaded
EXT4 FS on dm-0, internal journal on dm-0:8
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
swap_cgroup: uses 1504 bytes of vmalloc for pointer array space and 1540096 bytes to hold mem_cgroup pointers on swap
swap_cgroup can be disabled by noswapaccount boot option.
Adding 1540088k swap on /dev/mapper/vg_thinkpad-lv_swap. Priority:-1 extents:1 across:1540088k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
Capping off P-state tranision latency at 20 uS
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
JBD: barrier-based sync failed on dm-0:8 - disabling barriers
e100: eth0 NIC Link is Up 10 Mbps Half Duplex
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[drm:radeon_gem_do_relocate] *ERROR* radeon gem set domain -11 failed 0 4
eth0: no IPv6 routers present
fuse init (API version 7.11)
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
Intel ICH Modem 0000:00:1f.6: PCI INT B disabled
Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Intel ICH Modem 0000:00:1f.6: setting latency timer to 64

Module Size Used by
snd_intel8x0m 12940 5
fuse 49764 2
sco 9356 2
bridge 41496 0
stp 1944 1 bridge
llc 4788 2 bridge,stp
bnep 10888 2
l2cap 18912 3 bnep
bluetooth 44908 5 sco,bnep,l2cap
sunrpc 152416 1
nf_conntrack_netbios_ns 2096 0
ip6t_REJECT 3160 2
nf_conntrack_ipv6 11368 8
ip6table_filter 3136 1
ip6_tables 10728 1 ip6table_filter
ipv6 232512 26 ip6t_REJECT,nf_conntrack_ipv6
cpufreq_ondemand 6052 1
acpi_cpufreq 8220 0
dm_multipath 13636 0
uinput 6496 0
ppdev 6296 0
snd_intel8x0 27440 2
snd_ac97_codec 91752 2 snd_intel8x0m,snd_intel8x0
ac97_bus 1400 1 snd_ac97_codec
snd_pcm 62092 5 snd_intel8x0m,snd_intel8x0,snd_ac97_codec
thinkpad_acpi 53956 0
snd_timer 17896 1 snd_pcm
ipw2100 61144 0
hwmon 2148 1 thinkpad_acpi
snd 49084 17 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 5404 1 snd
libipw 22364 1 ipw2100
e100 28240 0
yenta_socket 21068 1
iTCO_wdt 10448 0
iTCO_vendor_support 2736 1 iTCO_wdt
pcspkr 2156 0
snd_page_alloc 7572 3 snd_intel8x0m,snd_intel8x0,snd_pcm
rsrc_nonstatic 9428 1 yenta_socket
lib80211 5064 1 libipw
i2c_i801 8056 0
joydev 8972 0
mii 4008 1 e100
parport_pc 22132 0
video 17380 0
output 2364 1 video
floppy 48052 0
nsc_ircc 14104 0
parport 28544 2 ppdev,parport_pc
irda 94544 1 nsc_ircc
crc_ccitt 1588 1 irda
ata_generic 4264 0
pata_acpi 3624 0
radeon 481928 2
drm 166144 2 radeon
i2c_algo_bit 4788 1 radeon
i2c_core 18016 4 i2c_i801,radeon,drm,i2c_algo_bit

dmesg.txt from scanModem on IBM Thinkpad R50 (4)

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29.6-217.2.3.fc11.i586 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.29.6-217.2.3.fc11.i586 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.29.6-217.2.3.fc11.i586 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (12278 buckets, 49112 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
IO APIC resources could be not be allocated.
Using IPI No-Shortcut mode
registered taskstats version 1
Magic number: 5:390:332
tty tty53: hash matches
Initalizing network drop monitor service
Freeing unused kernel memory: 424k freed
Write protecting the kernel read-only data: 1448k
Marking TSC unstable due to TSC halts in idle
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[drm] Initialized drm 1.1.0 20060810
radeon 0000:01:00.0: power state changed by ACPI to D0
radeon 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Detected VRAM RAM=32768K, accessible=32768K, BAR=131072K
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 1x mode
radeon 0000:01:00.0: putting AGP V2 device into 1x mode
[drm] setting agp_base to d0000000
[drm] setting agp_location to d0000000
[drm] DFP table revision: 2
[drm] Panel ID String: Samsung LTN150P1-L02
[drm] Panel Size 1400x1050
[drm] Default TV standard: NTSC
[drm] 27.000000000 MHz TV ref clk
i2c-adapter i2c-0: unable to read EDID block.
radeon 0000:01:00.0: VGA-1: no EDID data
i2c-adapter i2c-1: unable to read EDID block.
radeon 0000:01:00.0: DVI-D-1: no EDID data
allocated ee74c800 1400x1050 fb: 0x00040000, bo efa2d180
fbcon: radeondrmfb (fb0) is primary device
Console: switching to colour frame buffer device 175x65
[drm] LVDS-9: set mode 1400x1050 e
fb0: radeondrmfb frame buffer device
registered panic notifier
[drm] setting agp_base to d0000000
[drm] setting agp_location to d0000000
[drm] Loading R100 Microcode
[drm] writeback test succeeded in 2 usecs
[drm] Initialized radeon 1.30.0 20080528 for 0000:01:00.0 on minor 0
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
EXT4-fs: barriers enabled
kjournald2 starting: pid 61, dev dm-0:8, commit interval 5 seconds
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
Clocksource tsc unstable (delta = -198856672 ns)
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem dm-0 with ordered data mode
type=1404 audit(1251033576.322:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 8192 avtab hash slots, 128681 rules.
SELinux: 8192 avtab hash slots, 128681 rules.
SELinux: 8 users, 11 roles, 2767 types, 128 bools, 1 sens, 1024 cats
SELinux: 74 classes, 128681 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext4), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1251033576.638:3): policy loaded auid=4294967295 ses=4294967295
psmouse serio2: ID: 10 00 64<6>IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input6
udev: starting version 141
NET: Registered protocol family 23
nsc-ircc 00:0c: activated
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
irda0 (): not using net_device_ops yet
IrDA: Registered device irda0
nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500

dmesg.txt from scanModem on IBM Thinkpad R50 (3)

pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x3000-0x3fff
pci 0000:00:01.0: MEM window: 0xc0100000-0xc01fffff
pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000e7ffffff
pci 0000:02:00.0: CardBus bridge, secondary bus 0000:03
pci 0000:02:00.0: IO window: 0x004000-0x0040ff
pci 0000:02:00.0: IO window: 0x004400-0x0044ff
pci 0000:02:00.0: PREFETCH window: 0xe8000000-0xebffffff
pci 0000:02:00.0: MEM window: 0xc4000000-0xc7ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: 0x4000-0x8fff
pci 0000:00:1e.0: MEM window: 0xc0200000-0xcfffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000e8000000-0x000000efffffff
pci 0000:00:1e.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0x3000-0x3fff]
pci_bus 0000:01: resource 1 mem: [0xc0100000-0xc01fffff]
pci_bus 0000:01: resource 2 mem: [0xe0000000-0xe7ffffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 io: [0x4000-0x8fff]
pci_bus 0000:02: resource 1 mem: [0xc0200000-0xcfffffff]
pci_bus 0000:02: resource 2 mem: [0xe8000000-0xefffffff]
pci_bus 0000:02: resource 3 io: [0x00-0xffff]
pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
pci_bus 0000:03: resource 0 io: [0x4000-0x40ff]
pci_bus 0000:03: resource 1 io: [0x4400-0x44ff]
pci_bus 0000:03: resource 2 mem: [0xe8000000-0xebffffff]
pci_bus 0000:03: resource 3 mem: [0xc4000000-0xc7ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 3422k freed
Simple Boot Flag at 0x35 set to 0x1
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
type=2000 audit(1251033573.684:1): initialized
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1500
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
decode_hpp: Could not get hotplug parameters. Use defaults
acpiphp: Slot [1] registered
ACPI: AC Adapter [AC] (on-line)
Switched to high resolution mode on CPU 0
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (45 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 855PM Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial 00:0a: activated
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
serial 0000:00:1f.6: PCI INT B disabled
brd: module loaded
loop: module loaded
Fixed MDIO Bus: probed
input: Macintosh mouse button emulation as /devices/virtual/input/input3
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
ata1.00: HPA detected: current 189512482, native 195371568
ata1.00: ATA-6: FUJITSU MHV2100AH, 008400D8, max UDMA/100
ata1.00: 189512482 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2100A 0084 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 189512482 512-byte hardware sectors: (97.0 GB/90.3 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 189512482 512-byte hardware sectors: (97.0 GB/90.3 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
ata2.00: ATAPI: DW-225, 2.2B, max UDMA/33
ata2.00: configured for UDMA/33
scsi 1:0:0:0: CD-ROM TEAC DW-225 2.2B PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29.6-217.2.3.fc11.i586 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected

dmesg.txt from scanModem on IBM Thinkpad R50 (2)

Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20081204
ACPI: setting ELCR to 0200 (from 0800)
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 18108 entries in 72 pages
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (2790.78 BogoMIPS).
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=184 bytes
sizeof(task_struct)=3228 bytes
CPU0 attaching NULL sched-domain.
net_namespace: 1064 bytes
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 13:19:33 Date: 08/23/09
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: ACPI Dock Station Driver: 3 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xc0000000-0xc00003ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
HPET not enabled in BIOS. You might try hpet=force boot option
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x1860-0x186f]
pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
pci 0000:00:1f.3: reg 20 io port: [0x1880-0x189f]
pci 0000:00:1f.5: reg 10 io port: [0x1c00-0x1cff]
pci 0000:00:1f.5: reg 14 io port: [0x18c0-0x18ff]
pci 0000:00:1f.5: reg 18 32bit mmio: [0xc0000c00-0xc0000dff]
pci 0000:00:1f.5: reg 1c 32bit mmio: [0xc0000800-0xc00008ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:00:1f.6: reg 10 io port: [0x2400-0x24ff]
pci 0000:00:1f.6: reg 14 io port: [0x2000-0x207f]
pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.6: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xe0000000-0xe7ffffff]
pci 0000:01:00.0: reg 14 io port: [0x3000-0x30ff]
pci 0000:01:00.0: reg 18 32bit mmio: [0xc0100000-0xc010ffff]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:01.0: bridge io port: [0x3000-0x3fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xc0100000-0xc01fffff]
pci 0000:00:01.0: bridge 32bit mmio pref: [0xe0000000-0xe7ffffff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xb0000000-0xb0000fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:02.0: reg 10 32bit mmio: [0xc0204000-0xc0204fff]
pci 0000:02:08.0: reg 10 32bit mmio: [0xc0205000-0xc0205fff]
pci 0000:02:08.0: reg 14 io port: [0x8000-0x803f]
pci 0000:02:08.0: supports D1 D2
pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:08.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0x4000-0x8fff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xc0200000-0xcfffffff]
pci 0000:00:1e.0: bridge 32bit mmio pref: [0xe8000000-0xefffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: Power Resource [PUBS] (on)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
system 00:00: iomem range 0xcc000-0xcffff could not be reserved
system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
system 00:00: iomem range 0xdc000-0xdffff could not be reserved
system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
system 00:00: iomem range 0xe8000-0xebfff could not be reserved
system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x2fffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xffffffff could not be reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11bf has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x162f has been reserved
system 00:02: ioport range 0x1632-0x167f has been reserved
system 00:02: ioport range 0x1630-0x1631 has been reserved